Job Description

Job Location LSB El Dorado AR - El Dorado, AR 71730

The Maintenance Specialist position will support the general operations of the plant by servicing and maintaining the plant facilities, equipment, and vehicles in accordance with current applicable federal, state and local standards governing the Company to ensure that the plant is functioning properly, and production is maintained at all times. Multi-Craft Mechanic works in direct contact with other mechanics and personnel throughout the plant and reports directly to Maintenance Supervisor.

Responsibilities & Duties:

Receive work assignments and/or written work orders from supervisor and prioritize assignments; plan assignments in order to complete tasks in a timely and orderly manner; diagnose the source of equipment problems and determine the extent of repairs required; evaluate required repairs and determine proper method of performing repairs; determine and obtain from warehouse the proper parts and equipment required to complete repairs; mend, replace, repair, service and test equipment to ensure proper working order; take measurements; check clearances; ensure that defective or problem areas are cleared and secured properly and that electrical power is disconnected prior to any maintenance work being performed; spray and distribute gravel on roads, ditches and other areas; replace, change, pack, rebuild and overhaul worn or broken parts, including but not limited to flange gaskets, compressors, pumps, turbines, valves, lines, catalysts, hoses, steam tracers and traps, filters, gear boxes, bearings, lubricators, conveyor belts, seals, packing cases and other equipment throughout the plant; perform plate welding, pump and motor alignment, plumbing, insulation, carpentry and concrete foundation work and repairs; perform pipe fabrication, cutting, threading, fitting and installation; locate and repair steam leaks; determine the extent of equipment manufacturer and/or mechanical assistance required for proper repairs and coordinate repairs with supervisor and/or other mechanics; assist other mechanics with rebuilding major components; maintain written records and logs of repairs; identify problems and discrepancies, immediately report to supervisor and implement corrective actions to ensure proper operation of equipment; and, make determinations and use independent judgment concerning repairs of equipment.

Preventative Maintenance Functions

Perform inspections of equipment and determine the extent of preventative maintenance required; verify that equipment is functioning properly and is operating in a safe manner; plan assignments in order to complete tasks in a timely and orderly manner; service equipment and perform general preventative maintenance to comply with regulations, codes and standards; install, set up; determine the extent of equipment manufacturer and/or mechanical assistance required for proper equipment maintenance and coordinate equipment servicing with foreman and/or other mechanics; maintain written records and logs of preventative maintenance; identify problems and discrepancies, immediately report to supervisor and implement corrective actions to ensure proper operation of equipment; and, make determinations and use independent judgment concerning condition of equipment. others: ability to evaluate and interpret information and make independent decisions; and, ability to remain calm under stress.

Qualifications

Working Conditions:

• Overtime and availability to work non-standard hours required, including call in
• May be required to work around rotating and energized equipment, hazardous materials, and chemicals, in confined spaces or from elevated heights.
• Work outside in extreme weather conditions.
• Must be at least 18 years of age
• High school diploma or equivalent; demonstrate basic reading and writing skills
• Must demonstrate ability to follow oral and written directions
• Must be qualified and able to perform the duties and responsibilities of at least three of the following skills: General Mechanic, Welding, Millwright/Machinist
• Must demonstrate basic mechanical, welding, or machinist aptitude and knowledge of standards
• Five years previous experience in a mechanical, welding, or machinist maintenance capacity is preferred.
• Previous experience with basic hand tools, welding, automotive and/or machinist maintenance tools and equipment (electric drills, air wrenches, power tools, torches, welders, hoists, riggings, sprockets, chains, dial indicators, calipers, micrometers, safety, and protective equipment, etc.) Previous experience with the operation of vehicles, including but not limited to trucks, forklifts, pumps, cranes, manlifts used in plant operations
• Must be able to read, understand and utilize drawings, sketches, and blueprints
• Must demonstrate physical strength adequate to perform heavy manual labor
• Must be able to attend and complete on-the-job training
• Previous Laser Alignment experience a plus
• Completion of a vocational training program in industrial maintenance; or prior military experience in aviation or major weapon system maintenance is a plus

Physical and Sensory Requirements:

Walking; standing; sitting; reaching; bending; stooping; squatting; crawling; climbing stairs, ladders and equipment up to 100 feet in height; balancing; lifting, carrying and/or moving up to 50 pounds, occasionally while climbing and balancing; pushing and pulling up to and in excess of 50 pounds, with assistance from others; grasping and pulling, pushing, turning and working with hands, occasionally in close areas and while bending, stooping or squatting; good eye and hand coordination; active range of motion of arms, neck and trunk; ability to perform simple mathematical calculations; ability to read and write in English; communicate with others; ability to evaluate and interpret information and make independent decisions; and, ability to remain calm under stress.

Special Attention

The position is safety and security sensitive in nature.

This position deals with hazardous materials and/or industrial processes that can pose a risk to employees and the general public. This facility is required to comply with security standards under Department of Homeland Security (DHS) CFATS regulation 6 CFR Part 27.