Job Description
Lifting Supervisor – HDD & Microtunnelling Works
Location: Bahrain
Department: Operations / Tunnelling
Reports to: Construction Manager / Tunnelling Manager
Role: Site-based
Role purpose
The Lifting Supervisor is responsible for the safe planning, coordination, supervision and execution of lifting operations associated with Horizontal Directional Drilling (HDD), microtunnelling, shaft works and associated construction activities.
The role ensures that lifting operations are carried out in accordance with approved lifting plans, RAMS, project procedures, manufacturers' requirements and applicable Bahrain health and safety requirements.
Key responsibilities
- Supervise all lifting operations associated with HDD, microtunnelling and shaft activities.
- Conduct pre-lift briefings/toolbox talks with crane operators, riggers and banksmen before lifting activities commence.
- Ensure the correct crane, lifting accessories, rigging arrangement and lifting method are used.
- Verify crane capacity against lifting radius, boom configuration, load weight and ground conditions.
- Confirm operators, riggers and banksmen hold appropriate competency certification.
- Inspect the work area before lifting, including:
- crane positioning;
- outrigger deployment;
- ground bearing capacity;
- exclusion zones;
- overhead services;
- underground services;
- adjacent structures and plant.
- Confirm lifting equipment and accessories have valid inspection/test certification and are within their SWL/WLL.
- Ensure lifting accessories are correctly selected for the load, including slings, shackles, spreader beams, lifting beams and chain blocks.
- Establish and maintain effective exclusion zones around lifting operations.
- Maintain clear communication between the crane operator, banksman/signaller and lifting team.
- Stop any lifting operation where conditions differ from the approved lifting plan or where the operation becomes unsafe.
Supervise lifting and handling associated with:
- HDD drill rigs;
- mud recycling and separation equipment;
- high-pressure pumps;
- drill rods and tooling;
- reamers and hole openers;
- swivels;
- drill heads;
- pipe rollers;
- generators and ancillary equipment;
- product pipe/string handling;
- lifting and positioning equipment within HDD entry and exit areas.
- MTBM installation and recovery;
- jacking frames;
- thrust rings;
- intermediate jacking stations;
- slurry pumps and pipework;
- separation plant equipment;
- hydraulic power packs;
- tunnel pipes;
- service pipes and hoses;
- shaft access equipment;
- lowering and recovering equipment from launch and reception shafts.
Lift planning
The Lifting Supervisor shall review the approved lift plan before work starts and verify that actual site conditions correspond with the plan.
The supervisor must confirm:
- load weight and centre of gravity;
- crane configuration;
- lifting radius;
- crane capacity/utilisation;
- lifting points;
- rigging arrangement;
- accessory capacities;
- ground conditions;
- outrigger requirements;
- exclusion zone;
- communication method;
- environmental conditions, particularly wind;
- interaction with other plant and activities.
Documentation
Responsible for checking and maintaining site records including:
- approved lift plans;
- lifting permits where required;
- crane certification;
- operator competency certificates;
- rigger/banksman competency records;
- lifting accessory inspection records;
- pre-use inspections;
- toolbox talks;
- daily lifting equipment checks;
- equipment registers;
- defect/quarantine records.
- Qualifications and experience
Essential:
- Recognised Lifting Supervisor qualification/certification suitable for the project and accepted in Bahrain.
- Relevant lifting and rigging training.
- Minimum 5 years' lifting experience, preferably within heavy civil engineering, utilities, tunnelling, HDD, pipeline or shaft construction.
- Practical knowledge of mobile crane operations and crane load charts.
- Ability to understand lifting plans and rigging drawings.
- Good understanding of SWL/WLL, sling angles, load centres of gravity and crane working radius.
- Experience supervising riggers and banksmen.
- Good English communication skills.
Preferred:
- Previous HDD or microtunnelling experience.
- Experience with deep shafts and blind lifting operations.
- Experience handling tunnel pipes and heavy tunnelling machinery.
- Experience with crawler and mobile cranes.
- Recognised Banksman/Signaller and Rigging competency.
- NEBOSH, IOSH or equivalent HSE training.
- First Aid certification.
- Key competencies
The successful candidate should demonstrate:
- strong practical lifting knowledge;
- authority to stop unsafe operations;
- good communication with multinational workforces;
- ability to read crane load charts;
- sound understanding of rigging principles;
- good planning and coordination skills;
- strong awareness of simultaneous operations;
- disciplined control of exclusion zones;
- experience working around heavy tunnelling equipment.